Browse all guides ↓
Fohhn MA-4.600 four channel system amplifier

How to Choose a Power Amplifier for Installed Sound: Channels, Watts, 100 V and DSP

By Trianze Tech Team

Planning an installed sound system? Book a site survey or WhatsApp our AV consultants and we will propose the speakers, amplifiers and layout.

Choose an amplifier by channels (one per zone or speaker group), power per channel at the load you will connect (4 ohm, 8 ohm, 70 V or 100 V), the inputs your system uses (analog, AES/EBU or Dante), the DSP and presets your speakers need, and where it lives (rack size, cooling, noise and standby power).

1. Channels: One Per Zone or Speaker Group

Each zone with its own source or volume needs its own channel, and so does each speaker group that needs its own preset or delay: main speakers, fills, subwoofers. Four channel amplifiers suit most rooms; two channel models with more power per channel suit subwoofers and big point source speakers.

2. Power Per Channel and Impedance

Read the power at the load you will actually connect. Two 8 ohm speakers in parallel make 4 ohm; always stay at or above the minimum impedance the amplifier allows. For 100 V lines, add up the speaker taps and leave about 20 percent headroom.

Fohhn amplifier Channels and power Size Typical use
Fohhn MA-4.100 4 x 65 W, 4 Dante and 4 analog inputs 1U, half 19 inch Meeting rooms and small zones
Fohhn MA-4.600 4 x 600 W at 4 ohm, 100 V or 70 V 1U, 19 inch Halls, restaurants, multi zone installs
Fohhn MA-2.1200 2 x 1200 W at 4 ohm, 100 V or 70 V 1U, 19 inch Subwoofers and large point source speakers
Fohhn DI-4.1000 4 x 1000 W at 4 ohm, 100 V or 70 V 2U, 19 inch Auditoriums, events and mobile systems

3. DSP and Speaker Presets

Modern installation amplifiers include DSP for crossover, equalisation, delay and limiters. Many speaker makers publish presets for their models, and some require them: Fohhn states that its passive speakers need a Fohhn system amplifier with the correct speaker preset for full performance and operational reliability. For larger systems a separate DSP or matrix (for example from Biamp or Q-SYS) handles mixing, routing and echo cancellation, and the amplifier handles the speakers.

4. Inputs: Analog, AES/EBU or Dante

If the audio comes from a Dante network, a Dante amplifier removes converters and lets you route and monitor channels over the network. The Fohhn MA-4.600 and Fohhn MA-2.1200 come in analog (ANA) and Dante (DAN) versions, and the DI series takes plug-in input cards. Read our Dante and PoE speakers guide and how to choose a network switch for AV over IP.

5. Rack, Cooling and Standby Power

Check the rack space, the cooling and the power draw. The Fohhn MA-4.600 fits 1U, uses a temperature controlled fan and lists 45 W idle and 2 W standby, with Auto Power Save. In a quiet room or a lectern, choose fanless or low noise models; in a plant room, fan noise does not matter.

Quick Checklist

Question What to check
How many zones and speaker groups? Channel count, plus spares
What load per channel? Power at 4 ohm, 8 ohm, 70 V or 100 V, minimum impedance
Does the speaker need a preset? Same brand amplifier or published DSP settings
How does audio arrive? Analog, AES/EBU or Dante inputs
Where will it live? Rack units, cooling, noise and standby power

Amplifiers and DSP in Dubai and Abu Dhabi

Trianze Tech supplies amplifiers and DSP for auditoriums, hotels, mosques, offices and restaurants across the UAE. Browse amplifiers and DSP, Fohhn, Q-SYS and Biamp, and read 100 V line speakers and EN 54-24.

Call +971 58 161 3661 | Chat on WhatsApp

Frequently asked questions

How much amplifier power do I need for my speakers?

Match the amplifier channel to the speaker's rating at the impedance you will connect. A passive speaker rated 230 W nominal at 8 ohm, such as the Fohhn AT-10, sits comfortably on a channel that delivers several hundred watts, with the speaker preset or limiter protecting it. For 100 V lines, add up the transformer taps and leave about 20 percent headroom.

What does impedance mean when connecting speakers to an amplifier?

Impedance is the load the speakers present to the amplifier channel. Two 8 ohm speakers in parallel make 4 ohm, and four make 2 ohm. Always keep the total at or above the minimum the amplifier allows; the Fohhn MA-4.600, for example, has a minimum connection impedance of 4 ohm per channel.

Why do some speakers need a matching amplifier preset?

Many installation speakers are designed to run with DSP settings from their maker: crossover, equalisation and limiters tuned to that model. Fohhn states that its passive speakers need Fohhn system amplifiers with the correct speaker preset for full performance and protection. Without the preset the speaker can sound wrong or be damaged.

Should I choose an amplifier with Dante inputs?

If the audio already travels on a Dante network, from a DSP, a mixer or a Q-SYS core, a Dante amplifier saves converters and cabling and lets you route and monitor every channel over the network. The Fohhn MA-4.600 and MA-2.1200 come in an analog version (ANA) and a Dante version (DAN), so you choose at order.

How many amplifier channels do I need?

Count the zones that need separate volume, sources or processing, then add the speaker groups that need their own preset or delay. A meeting room with ceiling speakers and a subwoofer might need two or three channels, while a hall with main columns, fills and subwoofers may need eight or more. Spare channels make later changes easy.

Where can I buy installed sound amplifiers in the UAE?

Trianze Tech supplies system amplifiers and DSP from Fohhn, TOA, Q-SYS, Biamp and other brands in Dubai and Abu Dhabi with delivery across the UAE and GCC. Call +971 58 161 3661 or message us on WhatsApp for the best price and current stock availability.

Back to all guides